---
title: "How to draw blood with the Tasso"
description: "Every step from warming the arm to the pickup, with video guide – the one page for everything practical."
url: https://help.anivahealth.com/hr/articles/20-how-to-draw-blood-with-the-tasso
collection: "For pharmacies"
updated: 2026-11-15
language: hr
alternates: [de, en]
---

# How to draw blood with the Tasso

Every step from warming the arm to the pickup, with video guide – the one page for everything practical.

_Part 3 of 8 ·_ [_← What's in the starter kit?_](https://help.anivahealth.com/en/articles/21-whats-in-the-try-out-package.md)

* * *

This page has every step of the blood draw – from warming the arm to the pickup. The step list is deliberately brief enough to **print out and keep next to the test kit**. The workflow around it – consultation, report, follow-up revenue – is in [Your first test – step by step](https://help.anivahealth.com/en/articles/14-your-first-test-step-by-step.md).

## **Watch the video first**

Watch it once and you'll know the movement. After that the step list is just for looking things up.

Two notes on the video: it shows a tube from Tasso – you receive tubes from a different manufacturer. The procedure is the same: fill as full as possible, then turn the tube ten times top to bottom and back. And the video is **edited** – in real time a draw takes longer than it appears there. How long is in step 5.

## **Prepare**

1.  **Warm the arm – and drink beforehand.** These are the two biggest levers, and both decide between a good draw and a failed one. Rub the upper arm, tap it, or put a heat pack on it – **one to two minutes are enough**: a warm arm gives blood, a cold one doesn't. And whoever hasn't drunk enough beforehand gives hardly any blood – a glass of water first is part of the procedure, including when you test yourself.
    
2.  **Disinfect the skin.** Spray skin disinfectant from your own stock onto the upper arm and **let it dry for 10 seconds** – only then place the Tasso.
    
3.  **Lay out the right tube and attach it to the Tasso so that you can still see the fill marks on the tube.** The **red serum tube** for all values except blood sugar, the **purple EDTA tube** only for long-term blood sugar (HbA1c). **The tube overview for the appointment in the admin panel shows how many tubes you need** – usually it's one.
    

![](https://staticfiles.gleap.io/ghelparticle/uxz0NmWsGAZ4UNGSUDh5koJx3GUHEhFsFoqmZlAFMacVyhasKgDCWh9oOS1waaTOSXOvQd32loN.png)

![](https://staticfiles.gleap.io/ghelparticle/zCUAl1s0W6ZEbamTJbwTWdPrjNoDWFNggdJk7nVrA5zqkEH5RtzJloz8eM4uOABqg6uOC72Kg4R.png)

## **Draw**

![Where the Tasso goes: on the outer upper arm, on the vaccination muscle, three to four finger-widths below the shoulder bone](https://staticfiles.gleap.io/p693ca2ce07a6cdc8203949af/DwVgSxQzsguJ9BUOYjbgJwXNZRQbIB5jUDmD15pL5ln5YMAxyxDEwNBQTfR7rCwbG387rjJs4Tc.jpg)

4.  **Place the Tasso on the outer upper arm, on the vaccination muscle** – three to four finger-widths below the shoulder bone, above armpit level, as in the image. Then press the red button firmly; after the click, keep holding it for three seconds.
    
5.  **Let it run until the tube is as full as possible – expect three to four minutes, five at most.** On the red tube the upper mark is already at 500 µl – don't stop there as long as blood is still coming. Three or four minutes are normal and no reason to stop, even though it looks quicker in the video. After five minutes, take it off even if the topmost mark hasn't been reached: the blood clots, waiting longer achieves nothing. If it only reaches the lower mark, send it in anyway – a lot can usually still be analysed. How long it takes depends strongly on the warming. If the flow stops midway, a second firm press on the red button can help – sometimes it clears a blockage. To remove it, release the Tasso from the arm starting on one side, with the tube still attached; **once removed, the Tasso is used up** and must not be placed again.
    
6.  **Pull the tube off carefully with a slight twisting motion, then press the cap down firmly until it clicks audibly.** Only then is the tube sealed.
    
7.  **Invert the tube ten times, top to bottom and back.** Turn it slowly, as shown in the video – **do not shake**. Serum and blood not visibly mixing is normal.
    

**Tip – swapping tubes:** You can swap tubes: just leave the Tasso on the arm, take the tube off once the first one is full enough, attach a new tube and press the red button again for 3 seconds so the vacuum builds up again. Wait until the second tube has filled.

**The red tube has no separating gel**, so there is no layer at the bottom to watch out for. If you are using a yellow tube from an older kit: the layer at the bottom is a solid separating gel and must not mix with the blood. So invert rather than shake, and don't open the tube.

**Send the sample in even if it doesn't look nice.** Dark, uneven, small clots, less blood than expected – the lab centrifuges the sample anyway, and a result can usually still be obtained from what is there. Throwing it away definitely produces none.

## **Confirm**

8.  In the admin panel, open [Appointments](https://anivahealth.com/de/admin/appointments) and click the appointment, then **scan or enter the barcode for each tube and confirm the blood draw**. That tells us the sample is ready. We take care of the pickup: every evening we check which samples are ready and have them collected **on the next working day as standard**. So you don't have to wait for a courier or announce anything in advance.
    
9.  Store the sample until pickup – **room temperature is perfectly sufficient**; it does not need to be refrigerated and keeps overnight without a problem.
    

## **Pack**

10.  Tube into the sample bag – several tubes can go in one bag –, seal the sample bag and put it into the white shipping pouch. Several sample bags may share one pouch.
     
11.  Pull off the adhesive strip and seal the pouch. The courier brings the return label – you don't need to worry about it.
     
12.  **Nothing needs to be written on the tube or the shipping pouch** – no name, no address, no pharmacy name. The match runs exclusively via the barcode.
     

Something not working? The typical stumbling blocks are listed in [FAQ: The most common questions on your first test](https://help.anivahealth.com/en/articles/19-the-most-common-questions-on-your-first-test.md). Otherwise write to us via the **chat in the admin panel** – click the chat icon in the bottom right.

* * *

**Next in the track**

[

Your first test – step by step

From the consultation to the finished report: the full workflow in your pharmacy.

](https://help.anivahealth.com/en/articles/14-your-first-test-step-by-step.md)

[_← What's in the starter kit?_](https://help.anivahealth.com/en/articles/21-whats-in-the-try-out-package.md) _·_ [_All articles_](https://help.anivahealth.com/en/collections/4-fur-apotheken)
